How to Set up A Router for Home WiFi

People ask me occasionally about how to set up WiFi and make sure it’s secure. It’s not something that is easy to explain in person, it takes illustrations. So I’ve compiled it here.

First off, I suggest Linksys routers. If you don’t have one, go get a Linksys E2000 router. You can find them at Office Depot, Best Buy or most big box stores. I’ve also shamelessly added a link at the bottom of the page to get one on Amazon.

It isn’t totally necessary to get an E2000. An E1000, E2500, E3000, or Similar “E” router will have almost identical instructions. Most Cisco-Linksys routers will actually have similar screens.

Also grab some ethernet cable. You can buy this, make your own, or go to your IT guy’s office at work and ask if he has any spare pieces. You’d be surprised at how often the answer is, “Yes, how much do you need?” He might even be so happy for anyone coming around that doesn’t need to reboot their computer that he’ll make the cable for you. Your router will come with a piece, but you will need two pieces for the first setup even if you are going entirely wireless.

Step 1 – Unplug your modem from the power and disconnect it from your computer, or old router.

Step 2 – Look on the back of the router for the port (the hole) labeled “Internet” or “WAN”. Plug one piece of patch cable in here, and plug the other end of that cable into the modem’s Ethernet Port. Pro-tip: They look like big telephone jacks.

Step 3 – Plug the other piece of Ethernet cable into the port labeled “1” and plug the other end of that cable into your laptop or desktop’s Ethernet port.

Step 4 – Plug the router into power. Wait for the router to fully boot up. This usually takes about a minute.

Step 5 – Open the web browser on your computer and type “192.168.1.1” into the address bar and hit enter. Do not type this into the Google bar. See the picture below. Never mind that it says “192.168.227.1” in mine.

image

Step 6 – It will ask for a password. On Cisco/Linksys routers the username is “admin” and the password is “admin”.

Step 7 – My router had some Express setup screen that came up instead of what you see above. Just cancel that and get into the advanced setup screen. It’s not that complicated and I’m going to show you how to make things very secure.

Step 8 – Internet Setup – Leave the Internet Connection Type as “Automatic Configuration – DHCP”. Most Internet Providers don’t require a host name or domain name and you can leave MTU as default.

image

Step 9 – Network Setup – This is where we do things a bit different from most.

IP Address – The IP address is 192.168.1.1 by default. I would leave it like that. You’ll see in mine I’ve changed it. You can change the third number in the IP address to anything between 0 and 253 if you want.

If you change the IP Address write what you changed it to down. It’s important!

Subnet Mask – Leave this the default.

Device Name – You can change the device name to something different.

DHCP Server – Set DHCP server to enabled. The start IP address blank should be “100”. I always set Maximum Number of Users to 10, but if you have more than 10 Wi-Fi devices (laptops, phones, kindles, mp3 players, blu-ray players, XBOX, PS3, etc…) figure out how many you have and set this number to five or ten more than that.

Leave everything else here the default. It should fill the IP Address from above in the “Static DNS 1” blank.

Step 10 – Time Settings – Set this to your local time zone. You can see mine is wrong. It really doesn’t mean anything.

Step 11 – Click the “Save Settings” button. The router will reboot.

Step 12 – Close your web browser, wait a few minutes for the router to reboot.

Step 13 – Open the web browser and enter the IP address you change it to in Step 9, or the default “192.168.1.1” into your browser bar and hit enter.

If things work right the browser should open up to the page from before. If not, the easiest way to fix it is to reboot your computer.

On to the wireless set up!

Step 14 – Wireless – Click on the Wireless link at the top beside “Setup”. Change the Configuration View to “Manual” if it isn’t already.

Wireless Band – Select 2.4 GHz.

Network Mode – Select Mixed (this will allow a greater variety of devices to connect).

Network Name – Give your network a descriptive name, do NOT leave it as Linksys. Mine is “thegreentower”. You might want to name yours after your last name or something.

Channel Width – Leave this whatever the default is.

Channel – Leave this as Auto.

SSID Broadcast – Set to Enabled.

image

Step 15 – Click on Wireless Security and change the Security Mode to “WPA2 Personal”. If you have some really old devices you can set it to WPA.

DO NOT USE WEP! It is trivial to break WEP security. I’ve seen someone do it in five minutes.

Passphrase –  Enter a good 6 to 10 character password here. Something you’ll remember but that isn’t easy to guess. I’ve blacked mine out on the picture.

image

Step 16 – Click the “Save Settings” button at the bottom, reboot the router if you need to and you’re done!

The only other thing I would recommend doing is going to the Administration screen and changing the Router Password from something other than the default.

Congratulations!  You can now connect to your new, secure wireless network! Remember to enter the password you entered in step 15 to connect.

2 Replies to “How to Set up A Router for Home WiFi”

  1. Thank you so much for giving everyone an extraordinarily spectacular opportunity to check tips from here. It is always so fantastic and as well , full of fun for me and my office colleagues to visit the blog no less than thrice in 7 days to find out the fresh secrets you have got. And definitely, I’m just at all times amazed considering the special principles you give. Some 2 points in this posting are definitely the very best we have ever had.

  2. Pingback: Vanessa Bruno

Leave a Reply